FENNER TAPER LOCK PDF

Fenner Taper Lock® bushes are machined in cast iron and steel and are available in a full range of both metric and Imperial bores and keyways. They ha. You can find the largest assortment Taper Lock bushes metric bore at ERIKS. Choose from FENNER Taper Lock® bush metric bore size · Taper Lock® . Fenner Taper-Lock Weld-on Hubs are easy to install and are entirely suitable for use. where severe operating conditions are met. Tightening the screws.

Author: Dolkree Kagale
Country: Belarus
Language: English (Spanish)
Genre: Life
Published (Last): 11 September 2015
Pages: 451
PDF File Size: 20.74 Mb
ePub File Size: 11.89 Mb
ISBN: 736-8-54802-439-5
Downloads: 59745
Price: Free* [*Free Regsitration Required]
Uploader: Mezitilar

Taper Lock Bushes

Your password has been reset successfully. Last sold on Rs. All quality manufacturers will also supply an installation instruction sheet with the bush. Tighten the screws alternately until the bushing is loosened in the hub.

This will prevent cracking of the bush. Lightly tap against the busing to ensure it is seated squarely.

We will get back to you shortly! Taper bushes are available in both imperial and metric shaft sizes, ranging from 0. How to Fit a Taper Lock Bush. Note that special bores and keyway sizes can be supplied by CBC on request. Thanks for contacting industrybuying!

See example chart below figure 3or ask for this information at any CBC office. Ensure that the Taper Lock bush is free in the hub, then slip the ffenner onto the shaft and locate in the desired position. Insert screws into the holes that are threaded on the bushing side, as shown in Figure 2. The Taper Lock bush is pre-bored and keyed to match the required shaft and keyway diameters.

  ATMEGA164 DATASHEET PDF

Pack of 1 pieces. Then place the screws loosely into the holes that are threaded on the hub-side, as shown in Figure 1 below. Continue Browsing Continue to login. The screws are then tightened further.

Fenner Taper Lock Bushing 5050 Series 120 Mm Bore

Insert the correctly sized key into the shaft keyway, ensuring the key is a press fit into the shaft keyway. To view the demonstration video showing installation and removal of a Taper Lock bush, please Click Below; When installing or removing a Taper Lock bush, it is imperative that no lubrication be used between the taper.

Using a hammer and block, or sleeve, against the large end of the Taper Lock bush will help to avoid damage to the bushing. In sizes where washers are febner under the screw head, be sure to use these washers.

Fenner Taper Lock Bushing Series Mm Bore | eBay

Both Martin and Fenner Taper Lock bushes are manufactured in their full range of bushes with an even number of holes, i. Please share your feedback and help us improve! The Taper lock bush is manufactured from precision cast iron, and is machined to a high quality finish. The Martin and Lovk Taper Lock bushes featuring the fourth hole make them a preferred option in higher speed applications where balancing of loock drive is critical.

  ALBURNOIDES BIPUNCTATUS PDF

FENNER Taper Lock® bush metric bore size | ERIKS shop NL

The outside of the bush is tapered to match the component bore that is to be located on the shaft. Please note that there should always be one screw left over that is not used when removing the bushing. It is important to note that the holes need to be matched, not the threads.

Our representative will call you shortly to understand your requirement and offer you the best price. This design is dynamically balanced for high speed applications and is available off the shelf at CBC outlets in a range of sizes, from to Installation of a Fnner Lock Tapeer.

Warranty As per Fenner’s policy.

To sign in with your new password, Click here. The presence of lubricant on the tapered surfaces is not desirable, as the taper bushing relies on friction to operate effectively, and lubricants reduce friction. Please enter your e-mail address and we will send you a confirmation mail to reset your password.